TitleProduct

Transmission Line Steel Pole

  • Price:

    Negotiable

  • minimum:

  • Total supply:

  • Delivery term:

    The date of payment from buyers deliver within days

  • seat:

    Jiangsu

  • Validity to:

    Long-term effective

  • Last update:

    2018-12-18 08:44

  • Browse the number:

    455

Send an inquiries

Company Profile

Yixing Futao Metal Structural Unit Co., Ltd.

By certification [File Integrity]

Contact:ftjsgj(Mr.)  

Email:

Telephone:

Phone:

Area:Jiangsu

Address:Jiangsu

Website:http://www.futaometal.com/ http://ftjsgj.sinojiali.com/

Product Details


Transmission Line Steel Pole Introduction

The electric transmission line steel pole has a beautiful appearance. At present, in the wave of building cities and transforming cities, urban construction has higher and higher requirements for power line erection, which is also reflected in the requirements for its aesthetics. In particular, some urban landscape roads have stricter requirements in this respect.

Because of its compact structure and beautiful appearance, the electric transmission line steel pole can basically meet the requirements of aesthetics.

Quality galvanized pole cross arm for overhead power line

Height

From 8 meter to 55 meter

Suit for

Electric Power Transmission and Distribution

Shape

Polygonal or Conical

Material

Normally Q345B/A572, Minimum Yield Strength ≥ 345 N/mm²
Q235B/A36, Minimum Yield Strength ≥ 235 N/mm²
As well as Hot rolled coil from ASTM A572 GR65, GR50, SS400

Power Capacity

10kV to 500kV

Tolerance of the dimension

According to client’s requirement.

Surface treatment

Hot dip galvanized Following ASTM A 123, or any other standard by client required.

Joint of Poles

Slip joint, flanged connected

Standard

ISO 9001:2008

Length of per section

Within 14 meter once forming

Welding Standard

AWS (American Welding Society ) D 1.1

Thickness

1 mm to 36mm

Production Process

Raw material test → Cutting →bending →Welding (longitudinal )→Dimension verify →Flange welding →Hole drilling →sample assemble → surface clean→ Galvanization or powder coating ,painting →Recalibration →Packages

Packages

Packing with plastic paper or according to client’s request.


Product name

pole cross arm for overhead power line

Length of per section

Within 14m once forming without slip joint

Minimum ultimate tensile strength

490mpa

Max ultimate tensile strengt

620mpa

Installation way

The transmission poles below 20 meters are mostly directly buried, 

more than 20 meters, directly buried with flange installation. 

85ft above flange installation.

Power Poles can be classified into:

(1) Linear poles are widely used in flat areas, accounting for more than 80% of the total number of poles. They are mainly used to support wires, insulators, fittings, and other weights. They can bear lateral wind direction.

(2) Crossing pole is a kind of linear rod with tension line. It can not only be used for general linear pole, but also prevent large-scale reversing pole, which is used for less important crossing.

light bearing pole. It is used to prevent conductor breakage after insulator breakdown and is also used for common crossing places. 

(4) the corner bar is used at the corner of the wire rod to bear the resultant force on both sides of the wire.

(5) Tension-resistant poles are usually installed at intervals of about 1 km on a line. They can bear the tension of one side of the conductor and can limit the influence of short-line faults.

(6) the terminal bar is a tensioning pole set at the beginning and end of the line.

branches and cross poles for 10kV and below. From inside to outside, the branches are T-shaped, and the branches are crossed to the sides.

Pole longth(m)

8

9

10

11

12

13

15

Depth(m)

1.5

1.6

1.7

1.8

1.9

2.0

2.3

http://www.futaometal.com/